4.730+ Google reviewsRated 4.7 out of 5 from 30+ Google reviews

Glass Splashbacks Made in Sydney

Your kitchen deserves more than a flat-pack panel. Every Fields Glass splashback is measured in your home, then cut, toughened and painted at our own factory in Seven Hills. Nothing gets sent out to another supplier, so most jobs go from measure to installed in under a week.

Two Fields Glass glaziers pressing a pale green glass splashback into place between a kitchen benchtop and white overhead cupboards
  • Made in our Seven Hills factory
  • Measure to install in under a week
  • 35+ years in Sydney
  • NSW licence 213531C
  • Fully insured, $20 million public liability
Two Fields Glass glaziers holding a white glass splashback against the wall under a stainless steel rangehood in a new kitchen
Made in Seven Hills

What Is a Glass Splashback, and Is It Worth It?

A glass splashback is a panel of toughened safety glass, usually painted on the back, fixed to the wall behind your cooktop, sink or vanity. It replaces tiles with one smooth surface, so there are no grout lines to scrub and no joins to stain.

For most Sydney kitchens, it is one of the best value upgrades you can make:

  • Wipes clean in seconds. Oil, sauce and steam come off with a damp cloth.
  • Handles heat. Toughened glass is built to sit behind a working cooktop.
  • Makes rooms feel bigger. Glass and mirror bounce light around the kitchen.
  • Fits your wall exactly. We cut around power points, windows and rangehoods.
  • Keeps its colour. The paint sits behind the glass, protected from splatter and scrubbing.

Sydney Homeowners Trust Fields Glass

4.730+ Google reviewsRated 4.7 out of 5 from 30+ Google reviews
  • Quickly and easily got the job done. Very clean and tidy, very courteous and very much recommended for next time!

    Ashraf PirwaniGoogle review
  • Fields Glass have been doing our work for 15+ years with a wide range of different glass work, best in the business! Wouldn’t use anyone else!

    Evan GrahamGoogle review
  • Very happy with the service and prompt turn around. Brett was friendly, professional and efficient. Very satisfied with the job he did. Overall highly recommended.

    Suzanne TraceyGoogle review

Glass Splashback Colours and Finishes We Make

Back-Painted Colour Splashbacks

We paint the back of the glass at our factory, so the colour sits behind a glossy, wipe-clean face. Bring us a paint chip, a cabinet sample or the colour from your kitchen designer and we’ll match it.

Mirror and Tinted Mirror Splashbacks

A mirror splashback doubles the light in a narrow galley kitchen, butler’s pantry or bar. Choose classic silver or a tinted mirror in grey or bronze for a softer, moodier look. All our mirror splashbacks are toughened, so they are safe behind a cooktop.

Clear, Low-Iron and Satin Glass

  • Clear glass protects a painted or feature wall while letting it show through.
  • Low-iron glass removes the green tinge found in standard glass, so whites stay white and pale colours stay true.
  • Satin glass has a soft matte face that hides fingerprints and suits a modern, understated kitchen.
Glass splashback finishes, what each suits best and how it looks
FinishBest forLook
Back-painted colourMost kitchens and laundriesGlossy, any colour
Mirror / tinted mirrorSmall kitchens, bars, bathroomsReflective, adds light
Low-ironWhite and pastel kitchensTrue colour, no green edge
SatinBusy family kitchensMatte, hides fingerprints
A Fields Glass glazier scoring a sheet of glass on the cutting table in the Seven Hills factory

Why Our Splashbacks Go In Faster

Most splashback companies measure your kitchen, send the order to a glass processor, wait for it to be toughened, then wait again for it to be painted. Every hand-off adds days, and another chance for a mistake.

We do the whole job under one roof at 9/13 Foundry Road, Seven Hills:

  • Cutting, cutouts and polished edges, made to our own on-site measurements
  • Toughening, in house, the same process we use for our balustrades and pool fencing
  • Back-painting, mixed and applied at the factory

That means you deal with one team from quote to install, your splashback is usually on the wall in under a week, and if anything ever needs adjusting, we fix it here rather than reordering from a supplier.

Three Fields Glass glaziers fitting a long grey glass splashback behind a cooktop and rangehood in a new kitchen

Custom Glass Splashback vs Off-the-Shelf Panel vs Tiles

A Fields custom glass splashback compared with a retail glass panel and tiles
Fields custom glassRetail glass panelTiles
SizeMade to your exact wallFixed sizes (e.g. 600 x 700mm)Cut on site
Power point cutoutsCut at our factoryUsually noneCut by tiler
Colour choiceAny painted colour, mirror, low-iron, satinA few stock coloursHuge range
Joins and groutOne seamless panel or minimal joinsCovers cooktop only, gaps elsewhereGrout lines throughout
InstallationFitted by our teamDIY or handymanTiler, plus sealing

Kitchen, Bathroom and Laundry Glass Splashbacks

  • Kitchens: behind the cooktop, the full run between benchtop and overhead cupboards, behind sinks and in butler’s pantries
  • Bathrooms: behind vanities and basins, where they pair well with our frameless shower screens
  • Laundries: behind tubs and benches, where water and detergent marks wipe straight off
  • Commercial spaces: café counters, office kitchenettes and strata common areas
A Fields Glass glazier fitting a frameless mirror above a bathroom vanity

How Much Does a Glass Splashback Cost in Sydney?

Most supplied and installed glass splashbacks in Sydney cost between $450 and $1,500, with a typical single kitchen splashback around $850. Larger full-wall kitchen runs can reach $2,500. These are Sydney market ranges, and your exact price comes from an on-site measure.

What affects the price:

  • Size and number of panels
  • Number of cutouts for power points, switches and windows
  • Finish: mirror and low-iron glass cost more than standard clear
  • Removing old tiles or preparing the wall
  • Access, such as upper-floor apartments
Typical Sydney glass splashback prices
JobTypical Sydney range
Single panel behind a cooktop$450 to $850
Standard kitchen splashbackAround $850
Large or full-wall kitchen run$800 to $2,500
Glass, per square metre$330 to $420

Are Glass Splashbacks Safe Behind a Gas Cooktop?

Yes, when the right glass is used and clearances are met. Australian Standards require splashback glass next to a cooktop to be toughened safety glass complying with AS/NZS 2208. Where a gas burner sits closer than 200mm to the splashback, the wall behind it must also be non-combustible. New kitchens also need 650mm between the gas cooker’s pan support and the rangehood.

Every Fields splashback is toughened safety glass made in our own factory. We check burner clearances when we measure and will flag anything your gasfitter or kitchen builder needs to know before we make your glass.

Glass sheets stacked beside the cutting table in the Fields Glass factory, with a glazier cutting a pane

How Our Glass Splashback Service Works

  1. Free measure.

    Book it once your benchtops are installed. Stone benchtops change the height and level of the wall, and measuring before they go in is the most common reason splashbacks get remade.

  2. Choose your finish.

    We’ll talk you through colours, mirror tints and low-iron options for your kitchen.

  3. Made at Seven Hills.

    We cut, toughen and paint your splashback in our factory.

  4. Installed.

    Our team fits your splashback, usually in under a week from measure.

Tip: if any power points need moving, have your electrician do it before we measure, so the cutouts land in the right place.

Choosing the Right Splashback Colour

  • Lighter or darker than the benchtop? Contrast usually looks best: a dark benchtop with a light splashback, or the reverse.
  • White kitchen? Choose low-iron white so it matches your cabinets instead of looking slightly green.
  • Small or dark kitchen? A mirror or tinted mirror splashback adds the most light.
  • Want it to last? Whites, soft greys and mirror finishes stay in style far longer than bold feature colours.

Looking After Your Glass Splashback

Wipe it with a soft microfibre cloth and warm water or a standard glass cleaner. Avoid scourers and abrasive powders, and wipe oil splatter while it is still warm. That’s all the maintenance a glass splashback needs.

A Fields Glass glazier handling a freshly cut piece of glass in the Seven Hills factory

Glass Splashbacks Across Sydney

We make and install glass splashbacks across Sydney from our factory in Seven Hills, including Blacktown, Parramatta, Castle Hill, and the Seven Hills area, plus Western Sydney and the Hills District.

Western Sydney and the Hills
Seven Hills, Blacktown, Parramatta, Westmead, Castle Hill, Baulkham Hills, Kellyville, Bella Vista, Toongabbie, Rouse Hill, Penrith, Merrylands and surrounding suburbs.
Sydney Metropolitan area
The Inner West, North Shore, Northern Beaches, South West Sydney, the Sutherland Shire and the Eastern Suburbs.
A blue Fields Glass ute with a glass rack parked outside the Fields Glass factory in Seven Hills

Book Your Free Splashback Measure

Book a free measure and quote today. We’ll measure your wall, show you the finishes, and have your new glass splashback made and fitted within a week.

  • Free, obligation-free quote. We measure on site and price the job before any work starts.
  • Less waiting on glass. Your glass is cut in our own Seven Hills factory, not ordered in.
  • Licensed glaziers, 35+ years. NSW licence 213531C, and one team from measure to install.

Fields Glass Pty Ltd · 9/13 Foundry Rd, Seven Hills NSW 2147

Get a Free Quote

Send us a few details and photos of the job, and we’ll get back to you with a quote.

Frequently Asked Questions

How long does a glass splashback take to install?

Most Fields splashbacks go from measure to installed in under a week, because we cut, toughen and paint everything at our Seven Hills factory.

How much do glass splashbacks cost per m²?

In Sydney, glass for splashbacks typically costs $330 to $420 per square metre. Supplied and installed jobs usually range from $450 to $1,500 depending on size, cutouts and finish.

Can you put a glass splashback behind a gas cooktop?

Yes. It must be toughened safety glass to AS/NZS 2208, and if a burner is closer than 200mm to the wall, the wall behind must be non-combustible. We check this when we measure.

Can you cut around power points and windows?

Yes. We make all cutouts at our factory from our own on-site measurements, so every opening lines up.

Is a glass splashback better than tiles?

Glass has no grout lines, cleans faster, handles heat and makes a kitchen feel brighter. Tiles offer more patterns but need regular grout cleaning and sealing.

Why does my white glass splashback look green?

Standard glass contains iron, which gives it a green tinge. Low-iron glass removes it, so whites look truly white.

Do you make mirror splashbacks?

Yes. We make toughened mirror splashbacks in silver and tinted grey or bronze.

Call 24/7Free quote